|
|
| SUPER STOCK PULLING TRUCK
Call Ryan at 320-583-4243 for more information
- 1979 F-350 Pickup, Good Body ( hood has dents)
- Dana 60 w/military outers, 2 1/2 ton rear end, 5.83 Gears
- hydraulic lift body
- electric-hydraulic steering
- 34x18x15 Dick Cepek Bar Tires (old Style), 15x18 Steel wheels (Black)
- Ford 500 motor ran 1 season (12 hooks). Runs great.
Aftermarket Cast Iron Crank
Oliver Steel Rods
4.14 Stroke
0.030 over flat top pistons
Crane Cam Full Roller .714 Lift
Ford aluminum Cobra Jet heads, some work done to them.
Block filled.
Holley 1150 Dominator
MSD Distributor
Edelbrock Victor 460 Aluminum Intake
Schoenfeld vertical headers.
$8000.00
Call Ryan at 320-583-4243 for more information
posted/updated: 12 August 2010
|
FOR SALE
|
| FORD PARTS, PULLING PARTS, & OTHER STUFF
Call Brett Schuenke for more information
Cell: 320-766-4749 or Home: 320-732-2750
|
| ENGINES & RELATED PARTS
| 1970 Ford 351C complete truck pulling/race engine - SCJ cylinder heads with raised exhaust ports, best of everything inside, recently overhauled, never run since rebuild. Carrillo rods, Venolia pistons, tunnel ram intake w/flow-matched upper section. DOAE-L
SOLD
|
Set of New/Reconditioned Ford 460 cast iron cylinder heads Stock
$300 pair
| New/Reconditioned Ford 390 cast iron cylinder heads Stock
$300 pair
|
Two (2) Stock Ford 460 crankshafts
$20 each
| Ford 390 4WD oil pan and chrome valve covers
$50
|
Edelbrock Aluminum intake to fit 351W
$100
| One (1) set TFS fender exit downswept headers
$400 set
|
One (1) set TFS Zoomy headers w/covers
$200 set
| 350 Chevy RV cam & lifters, oil pan, & misc. parts
$100
|
|
| TRANSMISSIONS & RELATED PARTS
|
Ford C-4 automatic transmission (race-ready, manual shift body, for small block Ford)
SOLD
| COAN 5500 stall converter for C-4 transmission
SOLD
|
Transmission scatter blanket to fit C-4 transmission
SOLD
| New Process 435 4-speed transmission w/married 205 T-case
$150
|
New Process 205 transfer case to fit Ford (Complete in parts, Cleaned up case)
$75
| Two (2) New Process 435 4-speed transmission
$40 each
|
Ford C-6 automatic transmission (rebuildable) Big Block style
$20
| Ford C-4 automatic transmission (rebuildable) Sm. Block style
$20
| |
| DIFFERENTIALS & RELATED PARTS
|
1979 Ford Dana 60 front axle complete w/4.10 gears, sway bars, and brake calipers
$1,200
| 1975 Dana 44 complete front axle w/5.89 gears w/locking differential out of early style Bronco
$400
|
1966 Dana 44 complete front axle w/3.55 gears w/locking differential out of F100 pickup (C6TA-AG)
$400
| Two (2) Dana 80 35 spline axles (Stock)
$50 each
|
Dana 80 5.38 gear set
$150
| Dana 80 5.13 carrier assembly
$75
|
Dana 80 L/S carrier assembly
$200
| Dana 80 1550 series Yoke w/matching driveshaft slip yoke
$125
|
Two (2) Dana 70 4.10 ring gear only
$20 each
| Dana 60 front 4.10 gear set (1999 and newer)
$100
|
Dana 60 rear open carrier (Fine Spline, 31)
$20
| Dana 60 rear open carrier (Coarse Spline)
$20
|
Two (2) Dana 60 rear axle shafts (31 spline)
$20 each
| Dana 50 front open carrier
$50
|
Dana 44 3.54 gear set w/limited slip carrier
<
SOLD
| Dana 44 3.50 gear set w/open carrier
SOLD
|
Dana 44 3.50 gear set only
$75
| Ford 9" 5.83 gear set
SOLD
|
Ford 9" 3.50 gear set
$75
| |
|
| WHEELS & MISC PARTS
|
Four (4) Aluminum factory 18" 2007 Ford Mustang wheels
$75 each
| Four (4) 5-hole Ford 10" wide wheels (rusty)
$5 each
|
Three (3) 5-hole Ford 10" wide wheels (slots)
$5 each
| Two (2) 5-hole Ford 10" wide wheels (white spoke)
$5 each
|
Five (5) 6-hole Chevy white spoke wheels
SOLD
| Three (3) Steel 55 gallon barrels
$5 each
|
Two (2) Plastic 55 gallon barrels
$5 each
| Plastic Tool Box for pickup (inside rails)
SOLD
|
RV wind deflector (cab mount)
$20
| Plastic fuel cell for early style Bronco (under seat)
$20
|
1/2 ton Ford 4" lift kit - new in the box
$200
| |
|
Call Brett Schuenke for more information
Cell: 320-766-4749 or Home: 320-732-2750
posted/updated: 08 Aug 2010
|
| FORD PULLING PARTS
Call Mike at 866 280-2587 for more information
or EMAIL mike@mikescustomtrucks.com
- Crower 460 Ford 3 disc 11" with ring gear
Crower Bellhousing W/ starter pocket for Pro Fab reverser
with mated Pro Fab Reverser
All pieces sold only as a package
$3600.00
- Ford lift body
1992 Ford body with complete framework less hydraulics.
Call Mike at 866 280-2587 for more information
or EMAIL mike@mikescustomtrucks.com
posted/updated: 21 February 2010
|
| PULLING PARTS
Call Mike at 866 280-2587 for more information
or EMAIL mike@mikescustomtrucks.com
- Merlin BBC 81112
New block still in the bag
$2,350.00
- Cummins Common rail engine
P7100Pump
750 HP 1450 torque
S400 turbo
$9,500
- 461 cid BBC Blower engine
BDS 8-71 Stripped blower
20 amp MSD Pro Mag ignition
Complete and with Dyno sheets
$13,500
- 476 cid BBC engine
1000 CFM 4150 flange carburetor
MSD ignition
Fresh and complete with dyno papers
$8,500
- 1980 K30 Pro Stock pulling truck
Complete with above engine
$13,000
will consider parting out
- BBC 530 Cu. In.
New Merlin block
Lanatie internal bal 4.250 crank
Eagle rods
Ross Pistons
Crower Large roller cam
Dart 390cc heads
Edelbrock Victor dominator intake (no carb)
7AL MSD crank trigger complete ignition
$10,800 parts only
Assembly & engine dyno available for extra charge
Call Mike at 866 280-2587 for more information
or EMAIL mike@mikescustomtrucks.com
posted/updated: 21 February 2010
|
|
